Configuration

Load balancing

Load balancing controls how queries are distributed to nodes in a Cassandra cluster.

Without additional configuration the C/C++ driver defaults to using Datacenter-aware load balancing with token-aware routing. Meaning the driver will only send queries to nodes in the local datacenter (for local consistency levels) and it will use the primary key of queries to route them directly to the nodes where the corresponding data is located.

Round-robin Load Balancing

This load balancing policy equally distributes queries across cluster without consideration of datacenter locality. This should only be used with Cassandra clusters where all nodes are located in the same datacenter.

Datacenter-aware Load Balancing

This load balancing policy equally distributes queries to nodes in the local datacenter. Nodes in remote datacenters are only used when all local nodes are unavailable. Additionally, remote nodes are only considered when non-local consistency levels are used or if the driver is configured to use remote nodes with the allow_remote_dcs_for_local_cl setting.

/*
 * Use up to 2 remote datacenter nodes for remote consistency levels
 * or when `allow_remote_dcs_for_local_cl` is enabled.
 */
unsigned used_hosts_per_remote_dc = 2;

/* Don't use remote datacenter nodes for local consistency levels */
cass_bool_t allow_remote_dcs_for_local_cl = cass_false;

cass_cluster_set_load_balance_dc_aware(cluster,
                                       used_hosts_per_remote_dc,
                                       allow_remote_dcs_for_local_cl);

Token-aware Routing

Token-aware routing uses the primary key of queries to route requests directly to the Cassandra nodes where the data is located. Using this policy avoids having to route requests through an extra coordinator node in the Cassandra cluster. This can improve query latency and reduce load on the Cassandra nodes. It can be used in conjunction with other load balancing and routing policies.

/* Enable token-aware routing (this is the default setting) */
cass_cluster_set_token_aware_routing(cluster, cass_true);

/* Disable token-aware routing */
cass_cluster_set_token_aware_routing(cluster, cass_true);

Latency-aware Routing

Latency-aware routing tracks the latency of queries to avoid sending new queries to poorly performing Cassandra nodes. It can be used in conjunction with other load balancing and routing policies.

/* Disable latency-aware routing (this is the default setting) */
cass_cluster_set_latency_aware_routing(cluster, cass_false);

/* Enable latency-aware routing */
cass_cluster_set_latency_aware_routing(cluster, cass_true);

/*
 * Configure latency-aware routing settings
 */

/* Up to 2 times the best performing latency is okay */
cass_double_t exclusion_threshold = 2.0;

 /* Use the default scale */
cass_uint64_t scale_ms = 100;

/* Retry a node after 10 seconds even if it was performing poorly before */
cass_uint64_t retry_period_ms = 10000;

/* Find the best performing latency every 100 milliseconds */
cass_uint64_t update_rate_ms = 100;

/* Only consider the average latency of a node after it's been queried 50 times */
cass_uint64_t min_measured = 50;

cass_cluster_set_latency_aware_routing_settings(cluster,
                                                exclusion_threshold,
                                                scale_ms,
                                                retry_period_ms,
                                                update_rate_ms,
                                                min_measured);

Connection Heartbeats

To prevent intermediate network devices (routers, switches, etc.) from disconnecting pooled connections the driver sends a lightweight heartbeat request (using an OPTIONS protocol request) periodically. By default the driver sends a heartbeat every 30 seconds. This can be changed or disabled (0 second interval) using the following:

/* Change the heartbeat interval to 1 minute */
cass_cluster_set_connection_heartbeat_interval(cluster, 60);

/* Disable heartbeat requests */
cass_cluster_set_connection_heartbeat_interval(cluster, 0);

Heartbeats are also used to detect unresponsive connections. An idle timeout setting controls the amount of time a connection is allowed to be without a successful heartbeat before being terminated and scheduled for reconnection. This interval can be changed from the default of 60 seconds:

/* Change the idle timeout to 2 minute */
cass_cluster_set_connection_idle_timeout(cluster, 120);

It can be disabled by setting the value to a very long timeout or by disabling heartbeats.

Contents